Mitake 135mm F1.8 Lens Repair – Disassembly Guide

A while back I was at the Bargain Camera Show in Pasadena, and I saw a bit of an odd lens somebody  had. With its huge front element and ability to diminish even larger full-frame bodies, it was quite a striking piece of glass. I don’t remember the make of that particular one, but I do remember it being a 135mm F1.8
 
I don’t do a lot of portraiture, but the oddity/uniqueness of the 135mm F1.8 drew me and I eventually purchased one. I was delighted when it arrived, appearing to be in great condition and in a generic, but original box. Unfortunately, it turned out to have a tremendous amount of oil seizing the aperture closed.
 
I scoured the internet for quite some time, hoping to find some information about disassembling/repairing the lens, but while I came across numerous mentions of hazy elements, nothing actually described its disassembly, or even referenced having an oily aperture.
 
One of the only things I did find was a Flickr thread which discussed the existence of 135mm F1.8 lenses. My interest was specifically in my lens, badged “Apollo Low Light TV Lens,” which appeared in the following list taken from the thread.

Spiratone Plura-Coat, Porst, Computar, Promura CP Hi-Lux, Kenlock, Formula 5, Eyemik, Apollo, Accura, Varo, Vivitar and Weltblick.

Striking out on finding an existing repair guide for any of the listed lenses, I ended up doing the repair by trial and error, and documented the process. They’re such interesting lenses that it would be a shame to let any be thrown away or destroyed as a result of defects that could be repaired.
 

[section_break type=”line”]

Repair Guide

As far as lens repairs go, this one is very straightforward, but still requires patience and a little mechanical skill. Luckily, it requires very little in the way of tools.

  • Small Phillips screwdriver (I used a Husky 8-in-1)
  • Small flathead screwdriver (~1mm)
  • Gloves
  • Aperture-appropriate solvent such as Ronsonol, if you need to clean the aperture

 

Lens before disassembly

Lens viewed from the front, prior to beginning the disassembly process.
 

Lens after removing the rear mount and collar.

Just in front of the rear mount, containing the aperture control assembly, there are 3 flathead setscrews. Loosen them slightly, and hold the lens with the mount facing upward. The collar will slide down, revealing 3 Phillips screws which hold the mount and aperture control assembly down. Remove the screws and the rear assembly can be pulled straight off. These are the first 3 of a total of seven screws which must be removed, so don’t worry about mixing them up.
 

Setscrews

The next step is to remove the tapering trim ring, which is held in place with 3 setscrews. As before, just loosen them to the point where the ring can be pulled off. The photo shows just one of the three screws. Before removing it, it is convenient to use the guide printed on it to set the focus distance away from infinity. It will aid in the next step.
 

Gold limiting stops

After the previous step, you will see two gold-toned bits, each held on with two screws. These are the stops for the lens’ focusing assembly, and have tangs that slot into the helicoid assembly. Once the Philips head screws have been removed, the tangs can be removed. It is easier to remove them if the lens has been focused away from infinity as recommended in the previous step. Otherwise they bind, but may still be removed.
 

Prior to gut removal

This photo shows the lens just prior to removing its innards. With the stops removed, you can simply unscrew the inside parts from the outer shell/grip. Try to pay attention or mark the position of each of the 3 relative moving components relative to each other for reassembly. The grip and inside are directly related, but the ring to which the rear mount is attached can move independently of the other two, now that the tangs are removed.
 

Guts and gloryGuts and glory

The first of these two photos shows the entire inside assembly of the lens. The second shows the substantial front element assembly removed. It simply unscrews from the rest of the assembly. This is the part for which the gloves are required as the edges of the metal will cut you as you twist. [My hand is still healing at the time I write this].
The rearmost glass will also need to be removed but is a more simple task. If you cannot remove it with your hand, or while using a piece of rubber, then you should be able to use a metal ruler in the two grooves in the retaining ring for the glass.
 

Completely disassembled

This shows all of the main elements of the lens after being separated. This is as far as I went toward taking the lens completely apart, as I only needed to access the aperture assembly (contained in the piece with the male helicoid portion).
 
[section_break type=”line”]

Cleaning the Aperture

To clean the aperture, I used Ronsonol lighter fluid. It is an effective solvent and evaporates quickly and without residue. It does have a strong smell and is of course highly flammable, so you would be wise to work in a well ventilated area, free of spark or flame.
 
Using the lever, I closed the aperture down. After dribbling a few drops of Ronsonol onto the leaves, I shuttered the aperture open and closed to help dissolve the oils. Using a Q-tip, I gently wiped the blades. It may help to keep a finger gently pressed against the opposite side so as to not damage the leaves. Furthermore, be careful to wipe in the overlapping direction of the blades. If you go the opposite way, you risk not only bending them, but getting fibers trapped into the assembly.
 
As you repeat the process, you should see the ends of each new Q-tip you use becoming less soiled. It will start off blackening the cotton, but as it improves will be only slightly gray. Eventually, the assembly will become free, and the spring will retract the blades as it should. Even after it seems done, I recommend a last cleaning, and then allowing the blades to retract and sit at least overnight. There is still a little oil inside which will take some time to migrate to the leaves.
 
After a final cleaning with Ronsonol, you can make the blades look really clean by dipping a clean Q-tip in acetone (nail polish remover) and gently wiping the blades. Be careful with that, because it removes paint and melts plastic. It is the most effective way I have discovered for establishing cosmetically clean blades.
 
While this entire cleaning process will restore your the aperture to operational condition, it is not the most effective at removing all the oil, and it may soil the blades in time. Furthermore, if you do not clean up excess oil throughout the lens, you run the risk of re-contaminating the iris.
 
[section_break type=”line”]

Reassembly Notes

The reassembly is essentially the opposite of reverse. The hardest part will be reintegrating the helicoid assembly. Initial recombination of the two pieces will likely feel like it is not meshing, but it does require a surprising amount of force. There are also multiple positions they can mesh, which is why marking it earlier should help you put it back together. However, there is a limited number of positions, so if you made a mistake, you can solve it with trial and error.
 
Without markings, there are still some tips that can help with reassembly. The ring to which the mount attaches should be turned to the ‘infinity’ stopping point. The infinity position is when the lens assembly is closest to the camera’s sensor or film, so you can use that to determine which direction to turn it. The outer helicoid block has two slots for the tangs, and the inner piece has 3 slots. The two that are opposite need to be roughly aligned with the two in the outer block while it is being reassembled.
 
From there, there are only 3 positions which might be the correct angle for insertion; with the assemblies aligned straight, or with one helicoid groove offset to either side. From there, you can quickly reattach the mount (while skipping the intervening steps), and mount it on your camera to check infinity focus.
 
[section_break type=”line”]
I hope some people will find use in this guide and be able to improve or repair their old 135mm F1.8 lenses.
 
If you have any questions about the lens or about the process, you’re more than welcome to use the site’s contact box to reach me with your inquiries or corrections.
 
Thanks for stopping by!

Prev Minolta Maxxum 35-70mm F3.5-4.5 True Macro Modification
Next Sony A65 Full-Spectrum IR Conversion

8 Comments

  1. Thank you for a very good article. I have a Weltblick 135/1.8 with some dust inside. Not sure if I want to open it up or not but your page shows me what I would be getting into.

    • Most of the time internal dust, unless it’s extreme, won’t have any noticeable effect on the quality of images taken with it. As long as the dust is not too bad, and it’s mechanically working well, I would probably leave it be.
      I am glad you appreciated the guide and hope you enjoy the lens!

  2. Thank you for the great article!

    I Have a Porst 135 f.18 and I am in the process of cleaning it and apply new grease.
    Do you have any recommendations for this?

    I actually got the lens for 2 weeks now. The front element arrived already with a severe coating damage, and I would like to get a new element to replace it. Is this even possible or most likely I should buy a new lens?

    • I would have sworn I replied to this, but must not have done so.
      There are some greases specifically made for helicoids, but I think you could get by with almost anything that won’t melt badly when warm.

      I do not think you could get a replacement lens, but coating damage is somewhat treatable if you’re dedicated. You can polish the coating off with cerium oxide and use that as-is, or you can actually have it re-coated. Having either done by a professional will likely cost as much or more than the lens is worth.

      • Thank you for tour reply. In between I haver bought a lens spanner , a JIS screwdriver kit and helimax grease with index NLGI 1.
        I haver dissambled tem lens acording to to your instructions. The lens match exactly yours. Y was not able to completely remove the grease from the helicoid mounted on the lens iner barrel. This is because I was not able to disassemble those parts. I ALSO attempted to clean the oily blades but the oil keeps coming back after making some aperture variations.

        After applying new grease the reassemble was a a challenge. Ended up repeating the process a few times until get it done.

        I have then tested the lens in my d7100 and ended up disappointed. The images where very soft with very low contrast and no sharpness at all. This is how I was introduced to lens haze. Now I am in the process of cleaning the greasy film that lies in the lens. The front element damage will get attention latter. My lens have 5 elements in two groups. The first group consists of 3 non cemented lens and the second one is a cemented doubled. I will be trying the clean process with acetic acid and acetone as observed in lens cleaning tutorials. Can you kindly give me any recomendation on this?

        Also, after finishing it, I would really like to compare images with some that you might have.

        • The lens really isn’t the best lens, but nothing else I am aware of can compete for the same price. Wide open it is sharp but has CA and bloom. The detail it resolves is good, but muddied by those attributes. However, it does sound like your issue extends beyond that.

          The iris cleaning required many efforts. I cleaned it over and over again with Ronsonal. Was the haze there before cleaning the iris? Is it possible it is oily condensate that was left from an un-dry aperture assembly? I have sold my lens, but I think the oil came back, though it did not cause haze and didn’t prevent the aperture from operating like it originally did.

          Good luck with the haze and scratch removal. If you get it fixed, do let me know, since I’ll be happy to compare photos with my lens to yours.

  3. Just found this lens in a film repair shop, gathering dust and with a well-established colony of fungus.. The fungus was so bad that it had etched into the glass, but for 3 out of the 4 elements/groups this was mostly on the edges where it would have minimal effect. The rearmost element (a cemented doublet) instead had heavy hazing on the inside and scratches and coating loss on the outside where possibly some fungus had been wiped off rather vigorously and without dusting off the lens! So here I am, after having followed your instructions on dismantling the lens (thank you so much!!), trying desparately to clean the haze off the last element.. Being the one closest to the film/sensor it is likely to majorly affect the image quality.. Still, considering what I paid for it (a large bag of peanuts).. it’s more a fun project kind of scenario. Curious to compare it to my Nikon 135mm f2 AI lens.. just a tad slower but vastly more complicated in terms of lens elements. For sure this older design will not shine but at the same time it’s the widest 135mm lens I own and I’m quite excited to get it back to working condition. Hopefully I’ll have something worth posting about in a few days.

    • Well, considering the lens has some quirky image quality anyway, a few scratches and a bit of haze might be more help than hindrance! I had a lot of fun with this lens when I had it. I actually wouldn’t’ve gotten rid of it at all except I found a great deal on a Sigma YS mount 135mm F1.8 and head to head, my copy of the Mitake was slightly worse in terms of CA/fringe than the other, even if it might’ve had better overall contrast. Either way, they’re pretty fun lenses, and finding a 135mm F1.8 with even okay image quality would be impossible otherwise in this price range!

      I am glad my guide was able to help you out.